Electrocube, design manufacturer of electronic components

247A-248A Series

Film Capacitors Product Data Sheets

Metallized Polyester Plastic Case Quick Disconnect Capacitors Diagram

Metallized Polyester Plastic Case Quick Disconnect Capacitors

The 247A Series Snubber Capacitors were designed for AC applications such as motor start, motor run, fluorescent lamp ballast and other commercial applications. A wide range of rectangular epoxy case sizes are available with quick disconnect terminals. Wrap and fill designs are also available on special order.

Extended metallized polyester is used as the dielectric material.

Electrocube recognizes and supports the circuit design needs for specific mounting configurations, voltages and capacitances for capacitor models not shown. Special designs can be manufactured to meet any existing or future requirement.

For specific information on your product needs, contact your local sales representative or Electrocube directly.

The potting material and epoxy endfills of Electrocube’s capacitors meet or exceed the flammability requirements of UL94VO.

Dimensional variations for all MFD values are available with the same volume to meet your design requirements.

Specifications for 247A Series Metallized Polyester Plastic Case Quick Disconnect Capacitors

Capacitance Tolerance: ±10%
Temperature: -55°C to +70°C at rated voltage
Dielectric Voltage Test: Will withstand the application of 175% rated
DC voltage for a period not to exceed
1 minute at 25°C; current limited to 5 mA.
DC Life Test: Will withstand the application of 125% rated
VDC at 85°C for 1000 hours, with
not more than 1 failure in 12 permitted;
current limited to 5 mA
Dissipation Factor: Shall not exceed .35% at 25°C.
Acceptance Criteria: Measurement frequency for capacitance
and dissipation factor shall be 1000 Hz for
values less than 1 mfd and 120 Hz for
values of 1.0 mfd and up.
Insulation Resistance: At rated voltage or 500V, whichever
is less, units shall meet the minimum values:
TEMP. (°C) 25 | MEG x MFDS 1.oK
Terminals: 1/4” Quick Disconnect terminals
      Typical Dielectric Characteristic Curves

NOTES:

For information regarding insulating sleeves, mountings, special terminals, non-standard leads, circuit connections and other hardware, please consult factory.

For styles and ratings not shown, or for unusual requirements necessitated by special circuit applications (including higher IR or lower DF), consult the factory direct.

All Electrocube film capacitors have endfills and tape that meet or exceed the flammability requirements of UL94V0.

The 248A Series Snubber Capacitors were designed for AC applications such as motor start, motor run, fluorescent lamp ballast and other commercial applications. A wide range of rectangular epoxy case sizes are available with quick disconnect terminals. Wrap and fill designs are also available on special order.

Extended metallized polyester is used as the dielectric material.

Electrocube recognizes and supports the circuit design needs for specific mounting configurations, voltages and capacitances for capacitor models not shown. Special designs can be manufactured to meet any existing or future requirement.

For specific information on your product needs, contact your local sales representative or Electrocube directly.

The potting material and epoxy endfills of Electrocube’s capacitors meet or exceed the flammability requirements of UL94VO.

Dimensional variations for all MFD values are available with the same volume to meet your design requirements.

Specifications for 248A Series Metallized Polyester Plastic Case Quick Disconnect Capacitors

Capacitance Tolerance: ±10%
Temperature: -55°C to +70°C at rated voltage
Dielectric Voltage Test: Will withstand the application of 175% rated
DC voltage for a period not to exceed
1 minute at 25°C; current limited to 5 mA.
DC Life Test: Will withstand the application of 125% rated
VDC at 85°C for 1000 hours, with
not more than 1 failure in 12 permitted;
current limited to 5 mA
Dissipation Factor: Shall not exceed .35% at 25°C.
Acceptance Criteria: Measurement frequency for capacitance
and dissipation factor shall be 1000 Hz for
values less than 1 mfd and 120 Hz for
values of 1.0 mfd and up.
Insulation Resistance: At rated voltage or 500V, whichever
is less, units shall meet the minimum values:
TEMP. (°C) 25 | MEG x MFDS 1.0K
Terminals: 1/4” Quick Disconnect terminals

NOTES:

For information regarding insulating sleeves, mountings, special terminals, non-standard leads, circuit connections and other hardware, please consult factory.

For styles and ratings not shown, or for unusual requirements necessitated by special circuit applications (including higher IR or lower DF), consult the factory direct.


All Electrocube film capacitors have endfills and tape that meet or exceed the flammability requirements of UL94V0.

contact us   |   privacy policy   |   terms of use