Electrocube, design manufacturer of electronic components

330-351D Series - Metallized Polyphenylene Sulfide Capacitor

Capacitors Product Data Sheets

Metallized Polyphenylene Sulfide Capacitor

Metallized Polyphenylene Sulfide Capacitors

This metalized Polyphenylene Sulfide capacitor series exhibits superior electrical characteristics over an extremely wide temperature range.

Their miniature size, high Q, excellent IR and capacitance stability make them ideally suited to filter network and other low-loss high frequency applications.

A wide variety of sizes and configurations are available: axial-lead wrap and fill (in oval and round shapes) and rectangular epoxy case (axial and radial leads).

All capacitors feature extended foil construction and standard Tin-Coated Copper-Clad Steel leads. Nickel, Copper, Dumet and other special leads are available.

Protective clear wrap is offered on all wrap and fill units. Please add .010” to maximum T and W or dimensions for protective clear wrap.

The potting material and endfills of electrocube’s capacitors meet or exceed the flammability requirements of UL94VO.

Dimensional variations for all MFD values are available with the same volume to meet your design requirements.

Specifications for 330-351D Series Metallized Polyphenylene Sulfide Capacitors

Temperature: -55ºC to +125ºC.
Dielectric Strength: will withstand 200% at voltage and 25ºC for
a period not exceed 1 minute; current limited to 5 mA.
Life Test: will withstand 140% rated voltage for 250 hours at +125ºC
With not more than 1 failure in 12 permitted.
Dissipation Factor: shall not exceed 0.3% at 25ºC.
Acceptance Criteria: Measurement frequency for capacitance and
dissipation factor shall be 1000Hz for values
to 1 mfd; 120Hz. For values of 1 mfd and ov
Insulation Resistance: At rated voltage or 500V, whichever is less,
units shall meet the minimum values below:
Metallized Polyphenylene Sulfide Capacitor Temperature Range
Metallized Polyphenylene Sulfide Capacitor Typical Dielectric Characteristic Curve Graphs

NOTES:

For information regarding insulating sleeves, mountings, special terminals, non-standard leads, circuit connections and other hardware, please consult factory.

For styles and ratings not shown, or for unusual requirements necessitated by special circuit applications (including higher IR or lower DF), consult the factory direct.

All Electrocube film capacitors have endfills and tape that meet or exceed the flammability requirements of UL94V0.

Metallized Polyphenylene Sulfide Capacitors Diagrams by Electrocube
Specifications for 330-351D Series Metallized Polyphenylene Sulfide Capacitors Table 1
*Add tolerance designator to complete part number: F= ±1%, G= ±2%, J= ±5%, K= ±10%, M= ±20%
Specifications for 330-351D Series Metallized Polyphenylene Sulfide Capacitors Table 2
*Add tolerance designator to complete part number: F= ±1%, G= ±2%, J= ±5%, K= ±10%, M= ±20%
Specifications for 330-351D Series Metallized Polyphenylene Sulfide Capacitors Table 3
*Add Tolerance Designator to complete part number: F = ±1%, G = ±2%, J = ±5%, K = ±10%, M = ±20%
Specifications for 330-351D Series Metallized Polyphenylene Sulfide Capacitors Table 4
*Add Tolerance Designator to complete part number: F = ±1%, G = ±2%, J = ±5%, K = ±10%, M = ±20%
Specifications for 330-351D Series Metallized Polyphenylene Sulfide Capacitors Table 5
*Add tolerance designator to complete part number: F= ±1%, G= ±2%, J= ±5%, K= ±10%, M= ±20%
Specifications for 330-351D Series Metallized Polyphenylene Sulfide Capacitors Table 6
*Add tolerance designator to complete part number: F= ±1%, G= ±2%, J= ±5%, K= ±10%, M= ±20
Specifications for 330-351D Series Metallized Polyphenylene Sulfide Capacitors Table 7
*Add Tolerance Designator to complete part number: F = ±1%, G = ±2%, J = ±5%, K = ±10%, M = ±20%
Specifications for 330-351D Series Metallized Polyphenylene Sulfide Capacitors Table 8
*Add Tolerance Designator to complete part number: F = ±1%, G = ±2%, J = ±5%, K = ±10%, M = ±20%
Specifications for 330-351D Series Metallized Polyphenylene Sulfide Capacitors Table 9
*Add Tolerance Designator to complete part number: F = ±1%, G = ±2%, J = ±5%, K = ±10%, M = ±20%
Specifications for 330-351D Series Metallized Polyphenylene Sulfide Capacitors Table 10
*Add Tolerance Designator to complete part number: F = ±1%, G = ±2%, J = ±5%, K = ±10%, M = ±20%
Specifications for 330-351D Series Metallized Polyphenylene Sulfide Capacitors Table 11
*Add tolerance designator to complete part number: F= ±1%, G= ±2%, J= ±5%, K= ±10%, M= ±20
Specifications for 330-351D Series Metallized Polyphenylene Sulfide Capacitors Table 12
*Add tolerance designator to complete part number: F= ±1%, G= ±2%, J= ±5%, K= ±10%, M= ±20
contact us   |   privacy policy   |   terms of use